Adam

Hi Greg,

I think this is a better product in general, but its size makes it a bit awkward to use sometimes, so it’s a trade-off. Future DIY Packrafts will be designed to be easier to construct with irons this size.

Cheers!

Matt,
Before you wrote this blog, I decided to try one of the model aircraft heat sealing irons. I chose the Top Flight because it has a narrower bottom, and I thought it might be useful sealing across double width seams, where tubes join the floor, for example.
Using my inexpensive infrared thermometer (an instant read oven meat thermometer works just fine too) I found it heated to 198 degrees C. On removing the plastic thermostat knob, I could reach into the brass stem with a fine jewelers slotted screwdriver and adjust the thermostat. Turning the inner screw counter-clockwise increases the temperature. It doesn’t take much. 1/8 of a turn may be all you need. Double check it on a piece of TPU fabric, of course. I’ll post a picture on the forum.
I have also ordered one of the 220 volt leather irons from Aliexpress. I’ll let you know its dimensions and how it works when it arrives.

hello,
how much power you need for welding the tpu?
are 20W enough?
in germany i can get an iron which will make 240 till 280 grad celsius.

hello,
how much power you need for welding the tpu?
are 20W enough?
in germany i can get an iron which will make 240 till 280 grad celsius.

Hi Michael – I use the side and the bottom and the tip of the iron when working on the seams, depending on the situation. You can iron a strip narrower than the bottom of the iron by ironing over a convex bowl or narrower form (details in the V3 instructions), and you can also try putting masking tape on parts of the iron to insulate areas you don’t want to use. Cheers!

How much power you want depends on how much area you want to weld at once. A soldering iron may melt the material together, but when a complete boat consists of maybe a square meter of welding, the tip of a soldering iron makes maddeningly slow progress.

I have experimented with various soldering irons attached to a rheostat, an antique one with a big chunky copper tip worked the best. I also tried the clover iron, it gets the job done but is still slow at 40W. The whole thing of having a heating element far from the iron surface is maddening, as you are relying on all the heat you need for bringing fabric and underlayment up to temperature to travel down a skinny shaft. In addition, having this “lag” between your heat source and sealing surface makes for an iron that when laying about overheats, but when used cannot produce enough heat to weld efficiently. For example, the clover must be left sitting idle on it’s medium setting as to not get the tip hot enough to melt the nylon at initial touch. however, once in use it must be turned up to it’s highest setting to keep up with heat lost through the tip.

Matt’s suggestion of using the black baron heat sealing iron makes sense, as the heating coil is in the iron itself, and it appears to have at least a little thermal mass to it. I.e, the heat you make is the heat you get at the tip. I am waiting for the “21st century” cover rite iron to come in the mail, supposedly it keeps a temperature within 3 deg f.

I would rather use a clothing iron before I used a soldering iron!

In the last 12 months, I have built 4 cat-a-rafts and experimented with a few small pillows as well. I had 2 failed attempts, one reasonably functional raft and finally arrived at a design I am happy with. The point of that is that I have sealed a bunch of linear feet of fabric.
I started with the Mini Clover and graduated to the “improved” mini clover. (aluminum foil wrapped shaft) The out of the box version is painfully slow on 210 D fabric. The improved version is significantly better but it still requires waiting. It heats up to where it melts on contact (not good) then cools to where it’s not sealing requiring one to wait for it to heat up. Wait too long and it melts on contact. Not long enough and you don’t get much sealing done. The mini Clover does work much better with the lighter fabrics but they melt much easier when the iron is too hot so greater care is required.
Recently, I have been struggling with getting a pillow to hold air overnight with weight on it. If I can do that then I can build a raft that stays hard for long periods… I considered that the problem might be the new batch of fabric – especially the new 3 oz 40D. I mostly suspected my technique. I thought that I might be weakening the fabric at the seam edge when I hit it with a too hot iron. I suspected I was causing just enough damage to allow a very small amount of air seepage. As soon as I saw the video of Matt with the Black Baron I ordered it on Amazon. It was $26. As soon as it arrived I cut off the edges and resealed my last two pillow experiments. I achieved a good seal and no leakage. I put a 10″ x 10″ x 3/8″ steel plate on top of my most recent 40D experiment and it held air overnight. Mystery solved. I am now waiting for another batch of fabric and looking forward to working with the Black Baron iron. It is much more robust than the Mini. I broke my first Mini Clover after a decent amount of use and my current one is loosening up and likely to break in the near future. I don’t see how one could break the Baron. The adjustable temperature really helps and the larger mass holds the heat. As noted above, the Baron’s size helps solve some issues but at times can be a hindrance but overall, I think we are on to something here. Ron Samber

Yikes, that sounds scary! I’ve never used a sock, so maybe that’s the issue – wrapping an iron in an insulating blanket will certainly keep a lot more heat in. I’d avoid using a sock in the future.

I recommend against the 21st Century Iron altogether. Mine actually didn’t get hot enough and it lost its heat too quickly due to the shoe having less mass than the Black Baron iron. The 21st Century Iron looks good on paper and I’m sure it’s great for the thin fabrics that airplane modelers use, but for this application I don’t think it’s the right tool.

Matt: Thank you! I am one of those awaiting your input on this. I look forward to the video.
How does it compare to the red 40D taffeta? I will know soon enough as I ordered some a week ago but I would like your take on it as well. As always, I appreciate your efforts. Ron Samber

Yes, that’s right 🙂

Interesting… Yeah, I know of a couple of people who have tried using Cuben fiber and tape for inflatables, and the problem with the tape is that it migrates over time under pressure and eventually the seams pull apart (in a packraft, anyway – it seems to work fine for other applications where there’s less tension on the seams). It’s also prone to punctures, as you mentioned. The Porcher fabric sounds interesting, but I guess it would have to be sewn and taped.

I’m not sure, but regardless, I always recommend purchasing a fabric sample pack so you can compare fabrics directly.

It will be combined with single-sided fabrics.

There will be two different versions – one with a 1000D floor, and another with partial 1000D tubes as well. The price for the former will likely be similar to the current kits with double layer floors or a bit more, and the latter will be a bit more than that. The exact amounts will depend on how efficiently I can utilize the fabric. As I’ve said from the beginning, the point of the DIY Packraft project is to make packrafting more affordable.

What do you think about adding a layer of the new thick fabric on the inside floor of an existing packraft? Would it bond ok?

i’m so happy for you…
… and for us!
If each of us have a tear, and if we share all our tears, maybe we should create a lake to paddle on?

Hey Matt,

great news, nice to hear!

No, I’ll make an announcement on the blog whenever new products are available.

Yay! Im so glad its finally in your hands!! My order still says back ordered, will I receive my order soon now that you finally got the fabric? Is there any way to get an eta, it is a suprise gift for my husbands birthday…

Sorry to hear about you having to postpone your trip, but thanks for the update! I hope the news relieves some stress and maybe even a few good things start coming your way!

Oh what a bummer!! This must be why I haven’t received the order I placed on June 16th. I was really hoping to have this by tomorrow as a suprise for my husbands birthday. He has wanted one for soo long! Will I get a notification when it does ship?

Hi Brian – thanks for the tip. I’ve been in touch with the broker and freight forwarder on an almost daily basis and they both confirm it’s Customs holding it up, but yeah, I’ve had shippers, brokers, and forwarders screw things up in the past. I’ve learned not to sit back and assume everyone is doing their job perfectly all the time… unfortunately.

Hi Matt,
Please Hong Kong dollar to both display and drop-down.
Format is,
HK$1,234.56
Thousand separator is a comma.
Decimal separator is a full stop.
Two digits to the right of full stop (cents).

Thanks for adding and making our life easier.